Unlock/Jailbreak vom Iphone 2G mit der Version 2.x.x Durch QuickPwn (Windows)

POST

MAIL

Posted February 3, 2009 at 11:25pm by iClarified

Anleitung wie man sein Iphone 2G mit der Firmware 2.2 mit Hilfe von QuickPwn für Windows unlocked und jailbreaked. Bevor du beginnst kontrolliere, ob du iTunes auf die Version 8.0.2 geupdated hast.

Schritt 1
Erstelle einen Ordner namensPwnage auf deinem Desktop.

Lade die folgenden Dateien herunter und kopiere diese in den Pwnage ordner, den du eben erstellt hast.
- QuickPwn 2.2
- BL 3.9
- BL 4.6
- 2.2.0 (2G): iPhone1,1_2.2_5G77_Restore.ipsw

Entpacke die QuickPwn22.zip datei in den Pwnage ordner.

Unlock/Jailbreak vom Iphone 2G mit der Version 2.x.x Durch QuickPwn (Windows)

Schritt 2
Verbinde dein Iphone mit dem Computer und starte iTunes.

Wähle dein Iphone aus der Liste der Geräte auf der linken Seite aus. Halte nun Shift und drücke auf Wiederherstellen. Eine Wiederherstellung ist empfohlen, da dadurch kein Speicherplatz auf dem iPhone verschwendet wird.

Gehe zum Pwnage Ordner auf dem Desktop und wähle die 2.2 firmware ipsw aus. Drücke auf denOpen Knopf um vortzufahren

Schritt 3
Sobald iTunes mit dem Wiederherstellen deines Iphones auf die firmware 2.2 fertig ist, kannst du die QuickPwn.exe im Pwnage Ordner auf dem Desktop starten.

Schritt 4
Stelle fest, ob dein iPhone mit dem Computer verbunden ist und klicke den blauen Pfeil um fortzufahren.

Schritt 5
Klicke auf den Browse Knopf um nach deiner iPhone firmware zu suchen.

Schritt 6
Wähle die 2.2 firmware ipsw aus dem Pwnage Ordner auf deinem Desktop und klick dann den Open Knopf.

Schritt 7
QuickPwn wird prüfen ob die ipsw gültig ist. Klicke den blauen Pfeil um fortzufahren.

Schritt 8
Du kannst jetzt wählen, ob du Cydia oder Installer installieren möchtest, deine Bootlogos austauschen willst, und dein Handy unlocken willst. Wähle die, die du ausgeführt haben willst und klicke dann auf den blauen Pfeil um fortzufahren

Schritt 9
Jetzt wirst du gefragt deine bootloader dateien auszuwählen. Klicke auf denBrowse Knopf und wähle die 3.9 version des bootloaders aus dem Pwnage Ordner auf dem Desktop aus. Genauso tust du das mit der 4.6 version der bootloader datei. Dann klicke auf den blauen Pfeil um fortzufahren.

Schritt 10
QuickPwn wird dich jetzt fragen damit du bestätigst, dass dein iPhone per USB verbunden ist, bevor es weiterführt. Klicke jetzt den blauen Pfeil um fortzufahren.

Schritt 11
QuickPwn wird dein iPhone jetzt automatisch in den Recovery Mode versetzen. Sobald es in dem Recovery Mode ist, wirst du aufgefordert: Den Home Knopf für 5 sekunden zu drücken, Halte den Power und den Home Knopf für 10 Sekunden, dann lasse den Power Knopf los und drücke weiterhin den Home Knopf, bis dein Iphone im DFU modus ist.

Beachte genau die Anweisungen und folge ihnen.

Schritt 12
Sobald QuickPwn dein iPhone im DFU modus entdeckt, wird es automatisch mit dem Jailbreak- Prozess beginnen.

Schritt 13
Sobald der Jailbreak vollständig ist, wird QuickPwn dich darüber informieren, dass es erfolgreich war. Dein iPhone wird dann dazu übergehen BootNeuter zu starten. Dieser Prozess dauert ungefähr 5 Minuten. Bitte haben Sie etwas Geduld. Dein iPhone wird neustarten, wenn es den Prozess erfolgreich ausgeführt hat.

Follow iClarified

brandon - July 29, 2014 at 12:50pm

i need to unlock my mobile to all network

Reply · Like

eduardo - August 25, 2013 at 10:09pm

hola .. yo tengo un iphone 3g que me trade de usa. y quiero usarlo aqui en mexico con telcel . el problema que tengo es que cuando lo prendo me pide activarlo por medio de wifi o itune . cuando lo conecto por puerto usb a mi ordenador . me sale en el itunes que no tiene tarjeta sim .. no encuentro solucion a esto .. sabes el por que no me detecta la tarjeta sim !! o cual seria el problema .. gracias

Fawad Saeed - January 7, 2011 at 2:45am

Quick pawn software is not downloading. Please upload the file again, Thanks

Big papa - June 29, 2010 at 1:57am

hi my problem comes when i shift+restore my phone i use the provided restore file but it says iphone could not be restored and error occured(20) anybody know of any help to fix this?

Andreou - April 5, 2010 at 6:44pm

hi. i have a problem after the update. I can't switch off my iphone...it stays blocked till the battery is empty...

hasnul - December 8, 2009 at 6:31am

i did try all the steps and it turn accordingly but it didnt detect my sim card. plis help me? wut shud i do.

hasnul - December 8, 2009 at 6:29am

i did try all the steps and it turn accordingly but it didnt detect my sim card. i say no service. plis help me? wut shud i do.

Vivek More - October 17, 2009 at 6:01am

Nice set of user friendly steps. Just would like to add from my end: 1. The link to QuickPwn.zip seems to be dead. Use http://mytopfiles.com/archives/file/QuickPwn-225-2/304244.htm instead. 2. Mention the step to rename iPhone1,1_2.2.1_5H11_Restore.zip to iPhone1,1_2.2.1_5H11_Restore.ipsw 3. Mention the need of Microsoft .Net Framework 2.0 to run the QuickPwn

nadim - October 24, 2009 at 12:23pm

Itune recognize my iphone, I can click on the LHS but I don't see the restore button that I need tp press along with the shift, IT seem like I am missing something here. please help

nadim - October 24, 2009 at 2:22pm

I have firmware 3.1 on my iphone. When I connect to itune, it goes directly to the screen where it says to activate it with At&T. I don't see the screen where I can click the restore button along with the shift key. How to get that screen? Please help

juan - October 7, 2009 at 5:02pm

Thanks a lot.I finally could use back my iphone again.God bless you.

peter - October 5, 2009 at 10:34pm

i keep getting that error 20 when i restore the iphone and try to run it with iphone1,1 2,2 may it be because i have the 3.0 currently

ata - October 3, 2009 at 11:04am

thank u iClarified for these instructions, it works for me just perfect

damac - September 29, 2009 at 2:20pm

n yeah i have iphone 2g with 2.2.1(5h_11) version n thanks in advance.

damac - September 29, 2009 at 1:55pm

I unlock the phone succesfully And it detect the VOdafone India sim/network. Thank you. But there is a problem when I try to make a call it shows a message saying that I need to connect the phone to the itunes and only can make only emergency calls. through the emergency calls i can make phone calls but nothing more

anthony - September 26, 2009 at 8:29pm

thanks so much. Asante SAna, that swahili sayin THANKS

Jimmy - September 19, 2009 at 1:03pm

Hi I am from Singapore using M1 (if any1 knows). My 2G phone was jailbreaked n unlocked 2 yrs ago serial 7U746WBOWH8, using 1.1.3(4A93) modem firmware 04.02.13_G. I want to upgrade into 2.xx so i can use itunes application, but im not sure if this method will work for me??? any1 in singapore tried this before??? (email: antiphase214@yahoo.com.sg) thank you for reading

t4zz - August 21, 2009 at 3:13pm

This is for iphone 2g. When i get to "Wait for yout iphone to connect in Recovery Mode" it seems to stop there, i dont get no response. But while that does not respond when i press the home button and the powere button it starts the process after but then when it comes to the jailbreaking stages just on the last second of the 30 seconds it say either i have done the wrong process or the usb is faulty! i have tried it in a few usb ports, but yet no luck! Help is needed please , urgently thanks!

Jared - August 13, 2009 at 12:32pm

THIS TUTORIAL WORKED GREAT! I UNLOCKED MY IPHONE 2G IN LESS THAN 20 MINUTES EVERY OTHER PRGRAM I HAVE USED HAS NOT BEEN SUCCESSFUL LIKE THIS ONE. THANK YOU SO MUCH. -JARED

Yana - July 21, 2009 at 12:48pm

I used this tutorial and it worked perfectly! I did not have other SIM card, so I just took out ATT SIM card when unlocking my phone. Thank you for the great tutorial! If I upgrade to OS 3.0 will it lock my phone back?

Johndoe01 - July 21, 2009 at 1:41pm

There's a link on the top of the page if you want 3.0 firmware. The procedure to jailbreak and unlock is pretty much the same and also very easy to follow. Of course when you upgrade to any firmware, it will relock your iphone. The only problem I had is on both firmwares 2.1 and 3.0, the process doesn't work on Windows Vista, I got stuck in the middle of the process, I thought my iphone was bricked but when I switched to my other PC with Windows XP, it worked like a charm. I just had the new 3G iphone so I used this 2G iphone to practice, restored & unlocked, restored & unlocked so many times now that I can do it with my eyes closed! Just k/d!

TrickVistaToActXP - July 23, 2009 at 2:59pm

If you get an error in a middle of unlock process on Vista, you can use this trick: Before starting the Unlock/Jailbreak process, click the .EXE (redsn0w.exe), select Properties and go to 'Compatibility' tab, check 'Run this program in compatibility mode for' and select XP SP2 or Vista. This essentially tells the executable to run as if it was running in XP. After that you follow the instructions as they are. Works like a charm! You don't need to hunt for an XP machine. Btw, this works with any executable. So, if you have an application that doesn't run on Vista, you can use this trick. And it is a welknown compatibility method- not an hack- which is fully tested by Microsoft.

Manoj - July 11, 2009 at 6:19am

itunes 8.0.2 for 64 bit vista - http://notebook.driversdown.com/ViewDownloadUrl.asp?ID=139900&brNum=3&show=0 jailbreak - https://www.iclarified.com/entry/comments.php?page=3&enid=1880#commentsanchor unlock - https://www.iclarified.com/entry/index.php?enid=4253 steps: 1. the iphone restore did not work with shift + restore.. so i just restored (click restore without pressing shift), it downloaded 2.2.1 from apple website and restored it to factory settings. this was done to erase all previous used space and user settings etc. 2. after this, it was asking for activation, showing only emergency calls only etc.. i was kind of scared as nothing was accessible. 3. but i just continued with the jailbreak steps mentioned in https://www.iclarified.com/entry/comments.php?page=3&enid=1880#commentsanchor and it jailbroke the iphone with cydia installed. some relief here. 4. next was the most cumbersome (according to me) step of unlocking it for vodafone india sim. after googlinh reading many many docs and comments here and there, i realized that my modem firmware is at 2.30 where as yellowsn0w supports only 2.28, and the methods to downgrade were too complicated like using ssh and typing cmds etc.. 5. so i upgraded my modem firmware (not iphone OS) to 4.26 using "fuzzyband 3.1b1" . this can be installed by searching in cydia, it detects the current modem firmware and upgrades it from 2.30 to 4.26 6. next i used ultrasn0w to unlock the iphone for india vodafone sim using the instructions at https://www.iclarified.com/entry/index.php?enid=4253 . here make sure you turn 3g off.

jailbreaker - July 3, 2009 at 8:20pm

when i download the firmware it pops up as a folder i am useing a mac do i have to be on windows?

More Comments