Como usar seu iPhone como um Touchpad (Windows)

POST

MAIL

Posted February 21, 2008 at 6:18pm by iClarified

Essas são instruçoes de como usar seu iPhone como um Touchpad sem-fio com o seu computador Windows.

Passo 1
Selecione Installer na sua tela do iPhone.

Como usar seu iPhone como um Touchpad (Windows)

Passo 2
Selecione Sources que está na parte inferior da tela.

Passo 3
Selecione Edit no topo direito da tela.

Passo 4
Selecione Add no topo esquerdo da tela (sinal de +).

Passo 5
Digite http://cnp.qlnk.net no campo e depois aperte no grande botão OK.

Passo 6
Selecione Done no topo direito da tela.

Passo 7
Selecione Install na parte inferior da tela.

Passo 8
Selecione Utilities na lista de categorias (categories).

Passo 9
Selecione Touchpad na lista de pacotes (packages).

Passo 10
Selecione Install no topo direito da tela.

Passo 11
Selecione o Grande botão Install que aparecerá.

Passo 12
Quando o Touchpad terminar de instalar voce será direcionado a lista de Categorias. Pressione o botão Home para retornar a tela inicial do iPhone, então selecione o icone Touchpad para abrir o programa.

Passo 13
Agora no seu computador baixe e instale o TightVNC em here

Passo 14
Abra um TightVNC Server selecionando da lista de programas.

Passo 15
Modifique o Primary password e View-only password para uma senha de sua escolha..

depois clique no botão Apply.

Passo 16
Abra a tela executar no seu desktop.Digite cmd no campo e clique no botão Ok.

Passo 17
Quando a Tela de comando aparecer, digite ipconfig /all e pressione a tecla Enter. Anote o seu endereço IP.. nesse caso o meu IP é 192.168.0.199.

Passo 18
De volta ao seu iPhone, rode o Touchpad na tela principal.

Passo 19
Pressione o botão + no topo direito da tela.

Passo 20
Agora aparecererá a tela Edit Server. Entre com o nome do computador que voce vai estar se conectando. Entre com o endereço do computador tambem.( voce pode achar esse endereço na tela do passo 17). Entre com a senha que voce escoheu no passo 17. Agora que voce entrou com todas essas configuraçoes, voce pode pressionar o botão Save no topo direito.

Passo 21
Agora que voce configurou o seu servidor voce pode selecionar na lista de servidores.

Passo 22
Agora que voce se conetou ao seu conputador, voce pode usar o seu iPhone como um Touchpad!!!

Agradecimentos***: Grande agradecimentos vão para Jahanzeb por ter criado esse aplicativo.

Follow iClarified

ryan - October 2, 2008 at 8:39am

is touchpad for firmware 2.1 out yet?????

Reply · Like

Leandro - March 28, 2008 at 4:25pm

It´s worked fine for me! iPhone 1.1.2

Kendall - February 27, 2008 at 7:46am

Can be anything you can run a VNC server on. TightVNC is good enough. Check out their website for the requirements.

hsdgn - February 26, 2008 at 8:59pm

do i need to have "vista" running on my PC, or can i use any windows???

Kendall - February 24, 2008 at 10:45am

@reboot: For gnome, go to System -> Preferences -> Remote Desktop. VNC is installed with the default GNOME installation, but not enabled. Check the top two boxes and the bottom two if desired. VNC is a platform-independent protocol... life saver for Linux :D I would not recommend using this client on the iPhone, though. VNsea in the Network category works just as well - I beleive it's the same package, and it doesn't require extra sources.

Herman - February 24, 2008 at 5:18am

Does anybody know the default password of thightVNC? It would be so much easier to have tht saved in your iPhone, instead of always havinf to change the password to the choiche you selected.

leo114 - February 24, 2008 at 5:06am

Hi iclarified, I think many people will have using App problems on 1.1.3. Maybe can use the first time, then the App cannot run again & go to the spring board. Would you make any fixs to fix this problem? Thanks!!

marco - February 24, 2008 at 4:23am

Yesterday I had the same problem. I use Ziphone after restore my iPhone 1.1.3. I had a black display in recovery mode. I restore with Itunes in 1.1.3 and Ziphone 2.4. Now he work perfect and really fast. Better don't use this app.

marco - February 24, 2008 at 4:18am

Leo114 - February 24, 2008 at 3:01am

I HAVE INSTALLED IT IT WORKED OK BUT WHEN I TURNED OFF THE IPHONE AND TRY TO TURN IT BACK ON IT WILL NOT START UP.

Andrew Dennis - February 23, 2008 at 4:51pm

I HAVE INSTALLED IT IT WORKED OK BUT WHEN I TURNED OFF THE IPHONE AND TRY TO TURN IT BACK ON IT WILL NOT START UP!!!!!!!!! I JUST GET THE APPLE SIGN FOR A FEW MINS THEN I GET THE APPLE SIGN AND A SPINING WHEEL BEHIND IT BUT IT DOES NOT SPIN I HAVE PUT IT IN TO RESTORE MODE AND TRY TO RESTORE IT BUT GET AND ERROR I ALSO TRY TO UNLOCK IT WITH ZIPPHONE GUI2.4 BUT IT COMES BACK TO THE SAME SCREEN!!!!! PLEASE DO NOT TRY IT ON YOUR IPHONE AS MY IPHONE NOW DOES NOT WORK AND WAS WORKING FINE BEFORE ON 1.1.3

jesse - February 23, 2008 at 11:07am

it wont work....whenever i click it on my iphone it says the server closed the connection...what should i do i closed the firewall and everything but still no...i am on vista is that why???

marco - February 23, 2008 at 9:18am

hi guys somebody now if work on Vista??? I make connect but the mouse don't work. thanks

reboot - February 22, 2008 at 2:35pm

What about Linux? (Gnome)

marco - February 22, 2008 at 2:19pm

I think is XP.... nobody now ? :p

marco - February 22, 2008 at 1:32pm

Hi people it work with Vista or not? I connect but he don't work. Thanks

Yasir - February 22, 2008 at 9:35am

Hi iClarified, Please mention to disable the Windows XP SP2 Firewall to connect Tochpath with Windows PC successfully. Yasir Kuttiady

rpzab - February 22, 2008 at 9:08am

this is cool.

Ahmed - February 21, 2008 at 11:21pm

So cool mate, thanks